0
(12-09-2024, 11:58)mati75 napisał(a): https://www.thomas-krenn.com/pl/wiki/Program_Smartctl
Dzięki. Ten program mam zainstalowany ale jakoś nie wpadło mi do głowy aby go użyć.
Czy ktoś jest w stanie ocenić to na podstawie tego?
Poniżej wklejka:
Cytat:udo smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-119-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST Deskstar NAS
Device Model: HGST HDN724040ALE640
Serial Number: PK1334PEKDSJJS
LU WWN Device Id: 5 000cca 250f0134e
Firmware Version: MJAOA5E0
User Capacity: 4 000 787 030 016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Thu Sep 12 12:04:36 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 565) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 137 137 054 Pre-fail Offline - 79
3 Spin_Up_Time 0x0007 142 142 024 Pre-fail Always - 508 (Average 581)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 317
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 119 119 020 Pre-fail Offline - 35
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 29118
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 317
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1166
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1166
194 Temperature_Celsius 0x0002 130 130 000 Old_age Always - 46 (Min/Max 18/57)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 627
SMART Error Log Version: 1
ATA Error Count: 627 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 627 occurred at disk power-on lifetime: 29118 hours (1213 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 27 88 c4 08 Error: ICRC, ABRT at LBA = 0x08c48827 = 147097639
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 48 28 88 c4 40 00 03:33:14.571 WRITE FPDMA QUEUED
61 20 40 08 88 c4 40 00 03:33:14.571 WRITE FPDMA QUEUED
60 08 c0 78 88 40 40 00 03:33:14.571 READ FPDMA QUEUED
61 08 38 00 88 c4 40 00 03:33:14.569 WRITE FPDMA QUEUED
60 08 b8 38 88 80 40 00 03:33:14.568 READ FPDMA QUEUED
Error 626 occurred at disk power-on lifetime: 29096 hours (1212 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 58 28 88 80 06 Error: ICRC, ABRT at LBA = 0x06808828 = 109086760
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 20 10 88 00 40 00 00:20:22.476 WRITE FPDMA QUEUED
61 68 18 18 88 80 40 00 00:20:22.476 WRITE FPDMA QUEUED
2f 00 01 00 00 00 a0 00 00:20:22.476 READ LOG EXT
ec 00 00 00 00 00 a0 00 00:20:22.474 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:20:22.474 SET FEATURES [Set transfer mode]
Error 625 occurred at disk power-on lifetime: 29096 hours (1212 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 07 88 80 06 Error: ICRC, ABRT at LBA = 0x06808807 = 109086727
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 58 68 88 80 40 00 00:20:22.138 WRITE FPDMA QUEUED
61 38 50 00 88 40 40 00 00:20:22.138 WRITE FPDMA QUEUED
61 50 48 00 88 00 40 00 00:20:22.138 WRITE FPDMA QUEUED
61 38 40 00 88 c0 40 00 00:20:22.138 WRITE FPDMA QUEUED
61 08 38 00 88 80 40 00 00:20:22.138 WRITE FPDMA QUEUED
Error 624 occurred at disk power-on lifetime: 29096 hours (1212 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 70 10 88 00 06 Error: ICRC, ABRT at LBA = 0x06008810 = 100698128
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 48 00 88 40 40 00 00:20:21.799 WRITE FPDMA QUEUED
61 20 40 10 88 80 40 00 00:20:21.799 WRITE FPDMA QUEUED
61 80 38 00 88 00 40 00 00:20:21.799 WRITE FPDMA QUEUED
2f 00 01 00 00 00 a0 00 00:20:21.799 READ LOG EXT
ec 00 00 00 00 00 a0 00 00:20:21.798 IDENTIFY DEVICE
Error 623 occurred at disk power-on lifetime: 29096 hours (1212 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 71 0f 88 c0 05 Error: ICRC, ABRT at LBA = 0x05c0880f = 96503823
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 80 b8 00 88 40 40 00 00:20:21.449 WRITE FPDMA QUEUED
61 80 b0 00 88 c0 40 00 00:20:21.449 WRITE FPDMA QUEUED
e5 00 00 00 00 00 00 00 00:20:21.449 CHECK POWER MODE
2f 00 01 00 00 00 a0 00 00:20:21.448 READ LOG EXT
ec 00 00 00 00 00 a0 00 00:20:21.446 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 27983 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.