07-06-2020, 16:39
0
(07-06-2020, 08:18)dedito napisał(a): Dysk wygląda w porządku.
Jedynie wysoka wartość 13 dziwna i na dodatek taka sama jak 195.
Kod:
13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 1148040
....
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1148040Kod:
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warningDziś wziełem drugi dysk postawiłem taką samą konfigurację . Zaraz zobaczę czy jest podobnie ?
jest trochę inny
Kod:
sudo apt-get install -y gsmartcontrolKod:
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-32-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M7E (AF)
Device Model: SAMSUNG HM321HI
Serial Number: S2HZJ9BB308656
LU WWN Device Id: 5 0024e9 204bff6b7
Firmware Version: 2AJ10002
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Jun 7 16:42:53 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 4680) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 78) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 089 089 025 - 3411
4 Start_Stop_Count -O--CK 097 097 000 - 3622
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 6062
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 145
12 Power_Cycle_Count -O--CK 097 097 000 - 3592
181 Program_Fail_Cnt_Total -O---K 099 099 000 - 39007714
191 G-Sense_Error_Rate -O---K 100 100 000 - 3228
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 042 000 - 31 (Min/Max 14/58)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 62
223 Load_Retry_Count -O--CK 100 100 000 - 145
225 Load_Cycle_Count -O--CK 091 091 000 - 94211
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 4
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 [3] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 01 00 00 25 43 15 81 e0 00 Error: IDNF at LBA = 0x25431581 = 625153409
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.165 READ SECTOR(S) EXT
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.165 READ DMA EXT
24 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ SECTOR(S) EXT
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 03 28 00 e0 00 00:00:00.160 READ DMA EXT
Error 3 [2] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 01 00 00 25 43 15 81 e0 00 Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.165 READ DMA EXT
24 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ SECTOR(S) EXT
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 03 28 00 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 00 08 00 e0 00 00:00:00.159 READ DMA EXT
Error 2 [1] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 01 00 00 25 43 15 81 e0 00 Error: IDNF at LBA = 0x25431581 = 625153409
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ SECTOR(S) EXT
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 03 28 00 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 00 08 00 e0 00 00:00:00.159 READ DMA EXT
25 00 ff 00 01 00 00 00 00 00 00 e0 00 00:00:00.159 READ DMA EXT
Error 1 [0] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 01 00 00 25 43 15 81 e0 00 Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 ff 00 01 00 00 25 43 15 81 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 03 28 00 e0 00 00:00:00.160 READ DMA EXT
25 00 ff 00 01 00 00 00 00 08 00 e0 00 00:00:00.159 READ DMA EXT
25 00 ff 00 01 00 00 00 00 00 00 e0 00 00:00:00.159 READ DMA EXT
25 00 ff 00 01 00 00 00 00 00 00 e0 00 00:00:00.159 READ DMA EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 5589 -
# 2 Short offline Completed without error 00% 5589 -
# 3 Short offline Completed without error 00% 5323 -
# 4 Short offline Completed without error 00% 5323 -
# 5 Short offline Completed without error 00% 4741 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Aborted_by_host [90% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 31/33 Celsius
Lifetime Min/Max Temperature: 14/59 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (90)
Index Estimated Time Temperature Celsius
91 2020-06-07 06:05 31 ************
92 2020-06-07 06:10 29 **********
... ..( 2 skipped). .. **********
95 2020-06-07 06:25 29 **********
96 2020-06-07 06:30 30 ***********
97 2020-06-07 06:35 31 ************
98 2020-06-07 06:40 29 **********
99 2020-06-07 06:45 30 ***********
100 2020-06-07 06:50 30 ***********
101 2020-06-07 06:55 29 **********
102 2020-06-07 07:00 29 **********
103 2020-06-07 07:05 29 **********
104 2020-06-07 07:10 30 ***********
105 2020-06-07 07:15 31 ************
106 2020-06-07 07:20 31 ************
107 2020-06-07 07:25 30 ***********
108 2020-06-07 07:30 29 **********
109 2020-06-07 07:35 28 *********
110 2020-06-07 07:40 28 *********
111 2020-06-07 07:45 27 ********
112 2020-06-07 07:50 27 ********
113 2020-06-07 07:55 27 ********
114 2020-06-07 08:00 26 *******
115 2020-06-07 08:05 26 *******
116 2020-06-07 08:10 27 ********
117 2020-06-07 08:15 29 **********
... ..( 2 skipped). .. **********
120 2020-06-07 08:30 29 **********
121 2020-06-07 08:35 28 *********
122 2020-06-07 08:40 30 ***********
123 2020-06-07 08:45 29 **********
124 2020-06-07 08:50 29 **********
125 2020-06-07 08:55 29 **********
126 2020-06-07 09:00 28 *********
... ..( 2 skipped). .. *********
1 2020-06-07 09:15 28 *********
2 2020-06-07 09:20 30 ***********
3 2020-06-07 09:25 31 ************
4 2020-06-07 09:30 30 ***********
5 2020-06-07 09:35 30 ***********
6 2020-06-07 09:40 29 **********
7 2020-06-07 09:45 28 *********
8 2020-06-07 09:50 27 ********
9 2020-06-07 09:55 28 *********
10 2020-06-07 10:00 29 **********
11 2020-06-07 10:05 29 **********
12 2020-06-07 10:10 28 *********
13 2020-06-07 10:15 29 **********
14 2020-06-07 10:20 29 **********
15 2020-06-07 10:25 29 **********
16 2020-06-07 10:30 30 ***********
17 2020-06-07 10:35 29 **********
... ..( 2 skipped). .. **********
20 2020-06-07 10:50 29 **********
21 2020-06-07 10:55 28 *********
... ..( 3 skipped). .. *********
25 2020-06-07 11:15 28 *********
26 2020-06-07 11:20 29 **********
27 2020-06-07 11:25 29 **********
28 2020-06-07 11:30 28 *********
29 2020-06-07 11:35 29 **********
... ..( 4 skipped). .. **********
34 2020-06-07 12:00 29 **********
35 2020-06-07 12:05 30 ***********
36 2020-06-07 12:10 30 ***********
37 2020-06-07 12:15 30 ***********
38 2020-06-07 12:20 31 ************
39 2020-06-07 12:25 31 ************
40 2020-06-07 12:30 30 ***********
41 2020-06-07 12:35 29 **********
... ..( 4 skipped). .. **********
46 2020-06-07 13:00 29 **********
47 2020-06-07 13:05 30 ***********
48 2020-06-07 13:10 29 **********
... ..( 17 skipped). .. **********
66 2020-06-07 14:40 29 **********
67 2020-06-07 14:45 30 ***********
68 2020-06-07 14:50 30 ***********
69 2020-06-07 14:55 30 ***********
70 2020-06-07 15:00 31 ************
71 2020-06-07 15:05 31 ************
72 2020-06-07 15:10 29 **********
73 2020-06-07 15:15 31 ************
74 2020-06-07 15:20 31 ************
75 2020-06-07 15:25 33 **************
76 2020-06-07 15:30 33 **************
77 2020-06-07 15:35 33 **************
78 2020-06-07 15:40 32 *************
79 2020-06-07 15:45 32 *************
80 2020-06-07 15:50 33 **************
81 2020-06-07 15:55 34 ***************
82 2020-06-07 16:00 33 **************
83 2020-06-07 16:05 34 ***************
84 2020-06-07 16:10 33 **************
85 2020-06-07 16:15 32 *************
86 2020-06-07 16:20 34 ***************
87 2020-06-07 16:25 34 ***************
88 2020-06-07 16:30 34 ***************
89 2020-06-07 16:35 32 *************
90 2020-06-07 16:40 32 *************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 2 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific